Home About News Contacts Support Product Site Map
PRO LINE POWER LINE DISCO LINE LED LINE Mini SERIES DECO LINE
       
UA RU
 

 

POWER LINE

 
 

Dimmer Pack DP-4 SE

 

  A device is designed at rigid metal case suitable for mounting to the wall or to the frame. Power supply is monophase 220V AC. Various adjustments possibilities are available. Can work in two modes Ц dimmer or switcher. From the preceding DMX Dimmer Pack 4 it differs with the usage of standard euro power sockets as the outputs. A dimmer is available in two versions: 4x1kW and 4x2.2kW. Dimmer allows to change the power(brightness) at any of 4 channels independently. Switcher allows to turn on/off power at any of 4 channels independently. Dimmer provides a possibility to select among 15 soft lamp powering modes (Soft Start technology) and set minimal and maximal levels for each channel independently. A device has a passive cooling system, it is enabled with the various protection systems including short circuit protection and overheat protection. Devices supplied with a firmware version 3.1 have just a single curve of dimming regulation Ц a linear brightness changing.

 


 

Dimmer Pack DP-4 SE 2

 

  A device is designed at rigid metal case suitable for mounting to the wall or to the frame. Power supply is monophase 220V AC. Various adjustments possibilities are available. Can work in two modes Ц dimmer or switcher. From the preceding DMX Dimmer Pack 4 it differs with the usage of standard euro power sockets as the outputs. A dimmer is available in two versions: 4x1kW and 4x2.2kW. Dimmer allows to change the power(brightness) at any of 4 channels independently. Switcher allows to turn on/off power at any of 4 channels independently. Dimmer provides a possibility to select among 15 soft lamp powering modes (Soft Start technology) and set minimal and maximal levels for each channel independently. A device has a passive cooling system, it is enabled with the various protection systems including short circuit protection and overheat protection. Devices supplied with a firmware version 3.1 have just a single curve of dimming regulation Ц a linear brightness changing.

 


 

Dimmer Pack DP-121

 

   DMX Dimmer Pack DP-121 is a DMX512 enabled device intended to control a power (lamps brightness) at the light devices with no DMX module over the XLR wired connectivity. A device is designed at rigid metal case compatible with RACK 3U standard (132mm). Air flow is directed from left to right sides of the case. Dimmer allows to change power(brightness) at six 220V AC channels independently. Each channel can work either in soft power adjustment mode or in on\off mode. Dimmer allows to set minimal and maximal levels for each channel independently. Power supply is three-phased 220V. Each phase is wired to two output channels. Even if two of three phases will get cut off Ц the channels wired to the remaining phase will keep on working. A dimmer has an intellectual cooling system and protection systems including short circuit protection and overheat protection. Input of parameters is performed via the menu at digitizer.


 

Dimmer Pack DP-66

 

 DMX Dimmer Pack DP-66 is a DMX512 enabled device intended to control a power (lamps brightness) at the light devices with no DMX module over the XLR wired connectivity. A device is designed at rigid metal case compatible with RACK 3U standard (132mm). Air flow is directed from left to right sides of the case. Dimmer allows to change power(brightness) at six 220V AC channels independently. Each channel can work either in soft power adjustment mode or in on\off mode. Dimmer allows to set minimal and maximal levels for each channel independently. Power supply is three-phased 220V. Each phase is wired to two output channels. Even if two of three phases will get cut off Ц the channels wired to the remaining phase will keep on working. A dimmer has an intellectual cooling system and protection systems including short circuit protection and overheat protection. Input of parameters is performed via the menu at digitizer.


 

Transit three-phase splitter PD32T3916

 

  A device is designed at rigid metal case compatible with RACK 2U standard. Input is three-phase 220V AC over 5-pin 32A CEE power plug. Output lines are 9 monophase 220V 16A covered power sockets protected by circuit breakers of C-class. It has 3 power sockets at the front and 6 at the rear sides. Each phase is wired to 3 power sockets. Indicators showing current at each output. Rated total power of loads is up to 7 kW per phase, total is up to 21 kW. Type and manufacturer of input/output power sockets is negotiable.


 

End-line three-phase splitter PD32C3916

 

    A device is designed at rigid metal case compatible with RACK 2U standard.
    Input is three-phase 220V AC over 5-pin 32A CEE power plug.
    Output lines are 9 monophase 220V 16A covered power sockets up suitable for loads up to 3.5kW and protected by circuit breakers of C-class and Shuko grounding. It has 3 power sockets at the front and 6 at the rear sides. Each phase is wired to 3 power sockets. Indicators showing current at each output.
    Rated total power of loads is up to 7 kW per phase, total is up to 21 kW. Type and manufacturer of input/output power sockets is negotiable.

 


 

End-line three-phase splitter PD32C1416

 

  A device is designed at rigid metal case and equipped with 4 monophase 220V AC 16A (3.5kW) covered power sockets. Input is three-core wire with 4mm2 section and output is 32A professional plug. Input is protected with a circuit breaker. There are 2 LED indicators of power: one before the circuit breaker and another after it. Rated total power of loads is up to 7 kW per phase. Type and manufacturer of input/output power sockets is negotiable. Protection class is IP44.

 


 

End-line three-phase splitter PD63C3332

 

     A device is designed at rigid metal case compatible with RACK 3U standard.
    Input is three-phase 220-380V AC over 5-pin 63A CEE power plug.
Output lines are 3 5-pin 32A CEE power plugs.
    Indicators showing current at each output.
All output sockets are mounted at the front panel.
    Rated total power of loads is up to 13.8 kW per phase, total is up to 41.5 kW. Protection class is IP44. Weight 3,8 kg.

 


 

LIGHT CONSOLE

 

     Commutation panel provides a possibility to turn on and off light and other devices with just with a button hit. A device is designed at rigid metal RACK 19Ф compatible case and has a LED power indicator. Each channel is equipped with a personal fuse.
    Luminous switches lighting up once the channel is turned on and fade on turning off. Color grouping of channels makes work with the LIGHT CONSOLE really handy.

 


 

LIGHT CONSOLE PLUS

 

     Commutation panel for 8 groups of devices and soft adjustment of power at 4 channels. A must have solution for a podium or a small scene. The total quantity of channels is 12. A device is designed at rigid metal RACK 19Ф compatible case, has a LED power indicator and equipped with a general 63A circuit breaker.
    Each of 12 channels have personal fuse. Luminous switches lighting up once the channel is turned on and fade on turning off. Rated total power is 1100W per channel (5A). It is not recommended to use soft power adjustment channels for microprocessor driven devices as they are intended for simple devices like spotlights.

 


 

—»Ћќ¬џ≈ –ј«¬≈“¬»“≈Ћ»

 

  Anything that lights, plays or entertains us in any other way requires plugging into the power socket. While there are just a couple of devices it is enough to use a regular house hold extension cord. But once the quantity of devices is getting bigger and DMX enabled devices appear there arises a question: where to plug in them all? DLL has an answer for that question: we have everything to create a power supply network of any complexity level.






   
 

Power Line

DP-4 SE DP-4 SE 2 DP-121 DP-66 PD32t3916 PD32C3916 PD32C1416 PD63C3332 LIGHT CONSOLE LIGHT CONSOLE + POWER DISTRIBUTORS  
 

Copyright(c) 1997-2021. All rights reserved. Web-design and development by
DLL Design Group